Fluoro-Plastics, Inc.  Fluoro-Plastics, Inc. 1-800-262-1910
customerservice@Fluoro-Plastics.com
PTFE Sheet PTFE Plate PTFE Rod PTFE Extruded Tube PTFE Thin Film Reinforced PTFE Bondable PTFE PTFE Guide Rails, Rectangular Bar & Wear Strips PTFE Custom Profiles PTFE Machined Parts Modified PTFE PTFE Teflon Square Bar Molded Cylinders Gaskets
Search Catalog
      GO   
 All Categories    MODIFIED TEFLON ® AND PTFE
All Categories > MODIFIED TEFLON ® AND PTFE > MODIFIED TEFLON ® AND PTFE > Item # MOD020X24  
Download PDF Download PDF     Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Item # MOD020X24, MODIFIED TEFLON ® AND PTFE



Fluoro-Plastics offers modified PTFE basic shapes and machined parts. The new material offer engineering products with higher permeation resistance, lower creep, smoother surfaces and better high-voltage dielectric properties. Modified PTFE has the same performance characteristics of standard PTFE, viz. exceptional chemical resistance, high and low temperature capabilities, anti-stick performance and low friction.

Compared to standard PTFE modified PTFE displays remarkably enhanced performance characteristics. For example, the tensile strength and elongation of ordinary PTFE is 1500-2000 psi and 100-200%, whereas modified PTFE’s tensile strength is 4500 psi and its elongation at break is 500%. However, high voltage dielectric strength is where modified PTFE stands out: it is rated at 5200 volts per mil (at 1 mil), whereas standard PTFE is rated at only 500 volts per mil. In thicker sections the high voltage dielectric strength decreases, but not dramatically; Fluoro-Plastics offers modified PTFE which has been tested in 2.2, 3, 5, 8 and 10 mil thickness. The high voltage dielectric strength varied from slightly over 3,000 volts per mil at 2.2 mils to slightly over 2,000 volts per mil at 10 mils.

Also, parts and shapes made of modified PTFE can be assembled by heat welding and shaped by thermoforming. They can be joined without adhesives using moderate pressure in an oven, developing bonds with strength approaching that of the parts themselves. Welded sections can be subsequently thermoformed with no significant loss of strength. One of the simplest, most economical applications for modified PTFE is to make rectangular bags. A thin sheet can be folded over itself and heat sealed along two or three sides to make a bag for storing liquids and materials which must be protected from potential contaminants, e.g. in environmental or pharmaceutical sampling applications.

Fluoro-Plastics offers modified PTFE in skived sheets and rolls from one mil thick up to .125 inches thick, up to 48 inches wide, or slit to order. All rolls are packaged on a three inch cardboard core, or a three inch PVC core, to customer request.

Teflon® is a registered trademark of E.I. Du Pont De Nemours and Company used under License by Fluoro-Plastics, Inc. Only Dupont makes TEFLON®.





 Specifications   Applications of PTFE & Teflon®    ASTM Specifications   

Product Name

MODIFIED PTFE ROLLS .020" X 24"

Length (ft)

View
1

Thickness

.020"

Width

24"

Length

1 -200 ft per roll

Specification Sheet

ASTM D 4894 TY 3

Material Type

MODIFIED PTFE

Tensile Strength

4500 psi

Elongation at Break

450% +/-

Dielectric Strength,i.e. - Breakdown voltage

5200


 DOWNLOADS 

TYPICAL PROPERTIES OF PTFE
(JPG, 99KB)

FLUORO-MAR PROPERTIES
(JPG, 63KB)


 
Teflon is a registered trademark of Chemours LLC used under license by Fluoro-Plastics. Only Chemours makes Teflon.
 
Toll Free: 800-262-1910 • Local PA: 215-425-5500 • Fax: 215-425-5521• customerservice@Fluoro-Plastics.com
 
Copyright © Fluoro-Plastics • All Rights Reserved