REINFORCED PTFE & TEFLON® On Fluoro-Plastics, Inc.

1-800-262-1910
customerservice@Fluoro-Plastics.com

Chemours Licensee

HOME

PTFE Applications

PTFE Specifications

PTFE Properties

RFQ/Contact Us

PTFE Sheet PTFE Plate PTFE Rod PTFE Extruded Tube PTFE Thin Film Reinforced PTFE Bondable PTFE PTFE Guide Rails, Rectangular Bar & Wear Strips PTFE Custom Profiles PTFE Machined Parts Modified PTFE PTFE Teflon Square Bar Molded Cylinders Gaskets

Search Catalog



	All Categories REINFORCED PTFE & TEFLON®


All Categories > REINFORCED PTFE & TEFLON®


	REINFORCED PTFE & TEFLON®

	Click on a Product to view details.


		GLASS-FILLED COMPOUNDED PTFE AND TEFLON ® (24) Most widely used filler in various percentages (5%, 10%, 15% and 25%) Improves creep resistance, both at low and high temperatures Chemically stable (except for strong alkalis and hydrofluoric acid (HF) Little effect on the electrical properties of PTFE, and improves wear and friction behavior Compare to Rulon AR* SPECIFICATIONS From .010” to 2.5” thick From ½” wide to 48” wide Cylinders to 7” OD and 12” long Rod and Tube Material Type; reforcement filler plus PTFE: 25% short glass fibre; 85% virgin ... Search GLASS-FILLED COMPOUNDED PTFE AND TEFLON ® - 24 Items




		AMORPHOUS CARBON-FILLED ANTI-STATIC PTFE Anti-Static PTFE - Amorphous Carbon powder additive Increased hardness Increased thermal conductivity Adds to creep resistance Excellent wear properties when combined with graphite; carbon/graphite compounds preferred for non-lubricated piston rings Softer carbon additive lowers tool wear during machining, allowing machining to closer tolerances Carbon containing compounds have some electrical conductivity and are therefore anti-static SPECIFICATIONS From .010” thick to .250” thick From ½” wide to 48” wide Plate to 1” thick 48 inches square Cylinders to 7” OD and 12” long ...




		CARBON FIBER-FILLED PTFE Lower deformation under load Higher compressive and flex modulus and increased hardness Chemically inert–can be used in strong alkali and in HF, where glass reinforced compounds fail Good initial wear and rubbing or sliding characteristics in both dry and water applications Frequently used in piston rings to reduce cylinder wall wear SPECIFICATIONS From .010” thick to .250” thick From ½” wide to 48” wide Plate to 1” thick 48 inches square Cylinders to 7” OD and 12” long Rod Material Type; reforcement filler plus PTFE: 5% carbon fiber; 95% PTFE Max. PV ...




		GRAPHITE-FILLED PTFE Crystalline modification of high purity carbon Excellent wear properties, particularly against soft metals High load-carrying capability in high speed contact applications Chemically inert Frequently used with other filler, e.g. carbon SPECIFICATIONS From .010” thick to .250” thick From ½” wide to 48” wide Plate to 2.5” thick 48 inches square Cylinders to 7” OD and 12” long Rod Material Type; reforcement filler plus PTFE: 5% graphite; 95% PTFE Max. PV (psi-fpm); Mpa-m/s: 10,000; 0.35 Operating Temp.: minus 350F - plus 500F ...




		BRONZE-FILLED PTFE High percentage of bronze powder (40-60%) yields high thermal conductivity and better creep resistance Often used in hydraulic systems, particularly superb as linear bearings, e.g. slides, gibs, guide ways Not suited for electrical applications Bronze is attacked by certain chemicals Compare this product to Rulon 142* SPECIFICATIONS From 0.030" thick to 0.250" thick From 1/2" wide to 8.5" wide Available in cylinders up to 8" OD and 12" long (both solid rods and tubes) Material Type; reinforcement filler plus PTFE: 40%-60% Bronze powder; 60%-40% ...




		GLASS-MOLY-FILLED PTFE Adds to hardness and stiffness Reduces friction, especially starting coefficient of friction and steady-state wear Effect on electrical properties is negligible Unreactive chemically, and dissolves only in strong oxidizing acids SPECIFICATIONS From 0.010" thick to 0.250" thick From 1/2" wide to 12" wide Plate to 2.5" thick 48 inches square Cylinders up to 8" OD and 12" long (both solid rods and tubes) Material Type; reinforcement filler plus PTFE: 10-15% Glass fiber; 5% Molybdenum DiSulfide and 80-85% PTFE Max. PV (psi-fpm); Mpa-m/s: 10,000; ...




		MINERAL-FILLED PTFE PTFE with FDA compliant filler For food processing and pharmaceutical bearing applications Compatible with a wide variety of mating surfaces, both soft (e.g. mild steel) and harder surfaces Compare this product to Rulon 641* SPECIFICATIONS From 0.020" thick to 0.125" thick From 1/2" wide to 12" wide Available in cylinders up to 8" OD and 12" long (solid rods and tubes) Material Type; reinforcement filler plus PTFE: 15% Mineral Fill and 85% PTFE Max. PV (psi-fpm); Mpa-m/s: 10,000; 0.35 FDA Compliant: YES Operating ...




		POLYIMIDE-FILLED PTFE Low Friction Extremely low wear Increased hardness Operates well against soft mating surfaces like aluminum, mild steel, brass and plastics Ideal for stop-start applications to eliminate stick-slip Compare this product to Rulon J* SPECIFICATIONS From 0.020" thick to 0.125" thick From 1/2" wide to 12" wide Available in cylinders up to 8" OD and 12" long (solid rods and tubes) Material Type; reinforcement filler plus PTFE: 15% Polyimide and 85% PTFE Max. PV (psi-fpm); Mpa-m/s: 7500; ...




		STAINLESS STEEL-FILLED PTFE Extremely stiff and hard High loading percentage (50% generally) Available in both molded sheet and molded cylinders (rod and tube), up to 8" OD and 12" long SPECIFICATIONS From 0.020" thick to 0.250" thick From 1/2" wide to 12" wide Plate to 1.5" thick 24 inches square Cylinders to 7" OD and 12" long Material Type; reinforcement filler plus PTFE: 55% Stainless Steel; 45% PTFE Operating Temp.: minus 350 °F - plus 500 °F Attribute/Properties: Very hard, very stiff

	Teflon is a registered trademark of Chemours LLC used under license by Fluoro-Plastics. Only Chemours makes Teflon.
	Toll Free: 800-262-1910 • Local PA: 215-425-5500 • Fax: 215-425-5521• customerservice@Fluoro-Plastics.com
	Copyright © Fluoro-Plastics • All Rights Reserved